• English
    • Nederlands
    • Deutsch
    • Franšais
    • Espa˝ol

ES300
SERIES.

300 W DC Power Supplies

Unit Voltage range Current range
ES 030-10

0 - 30 V

0 - 10 A

Features:

    • Very low output ripple and spikes
    • EMC surpasses CE requirements: low emission & high immunity
    • High programming speed
    • Excellent dynamic response to load changes
    • Protected against all overload and short circuit conditions
    • Designed for long life at full power

Functionalities:

    • Master/Slave parallel and series operation with voltage and current sharing
    • Voltage and current control with 10-turn potentiometers
    • For laboratory use or optional 19” rack mounting

Specifications:

Input voltage (single phase) : 92-265 V AC (48-62 Hz)
Active Power Factor Correction (PFC) : 0.99 / 0.96 (at 100% load)
Efficiency : up to 86% (at full load)
Output ripple and spikes : 5 mV rms / 15 mV pp
Regulation : 10 mV (0-100% load step)
Recovery time : 50 Ás (50-100% load step)
Programming speed : 0.8 ms (10-90%)
Analog programming accuracy : 0.2%
Output voltage and current stability : 30.10-5 / 10.10-4
MTBF : 500.000 hrs
Operating ambient temperature -20 to +50 ║C

Standards:

Power supply standard : EN 61204-3
Generic Emission : EN 61000-6-3 (EN 55022B)
Generic Immunity : EN 61000-6-2
Safety : EN 60950 / EN 61010
Insulation input / output : 3750 V rms
Protection class : IP20

 

Dimensions and weight:

Width = half 19

Height = 66 mm (incl. feet)

Depth = 333 mm

Weight = 3.1 kg

Options:

  • Rear Power Output and Remote Sensing

    Output terminals at the rear panel instead of binding posts at the front panel, includes remote sensing. For more information download the data sheet ES300-series (see pages 1-3 & 1-4).

  • Sequencer

    Arbitrary Waveform generator or standalone automation. The sequencer is integrated in the Ethernet controller. For more information download the data sheet Ethernet Interface.

  • Increased Output Power

    For conservatively rated units extra output power (with the same reliability) is allowed. At some derating, either the maximum output voltage or current of these units can be increased by about 10%. Contact us or our local distributor for information which units extra output power is allowed.

  • 19-inch Rack Adapter

    Rack adapter sets for positioning the ES300 units in a 19-inch rack. For more information download the data sheet ES300 series (see pages 1-3 & 1-4).

      • RA19-1ES — for 1 unit
      • RA19-2ES — for 2 units side by side
      • RA19-ES-PSC —  for 1 unit ES with 1 external PSC-232 or 488 module side by side
      • RA19-ES-PSC-ETH—  for 1 unit ES with 1 external PSC-ETH module side by side
     
  • Software Control and Interfaces

    Factory installed programming interfaces*: 

      • Ethernet (incl. sequencer)
      • RS232
      • PROFIBUS
      • CANBUS

     

    External interface modules:

      • Ethernet module
      • RS232 module
      • IEEE488 module
      • ISO AMP module

     

    * there is room for only one of the interfaces in a unit and analog programming connector will be removed

Documents Document format Size
Data sheet CANopen and PROFIBUS interface PDF (Acrobat Reader) 201.5 KB
Data sheet Ethernet interface PDF (Acrobat Reader) 337.2 KB
Data sheet IEEE488 interface module PDF (Acrobat Reader) 257.9 KB
Data sheet ISO AMP module PDF (Acrobat Reader) 514.0 KB
Data sheet RS232 interface PDF (Acrobat Reader) 257.9 KB
Software CANopen and PROFIBUS interface Software 846.4 KB
Software Ethernet interface Software 490.4 MB
Software RS232 and IEEE488 interface Software 77.8 MB
Firmware
Full installation -
Upgrade -
Technical documents
Data sheet DATA_SHEET_ES300.pdf
Product manual PRODUCT_MANUAL_ES300.pdf
Application notes
Application note APPLICATION_NOTE_SAFE_OPERATION_POWER_SUPPLY.pdf
Software
Software -
Product Support

 

T: +31 111 413656
E: by filling out the contact form

 

Contact form
Sales Department

 

T: +31 111 413656
E: by filling out the contact form

 

Contact form